Adding regions in Diva Distro

It looks like I’ll be returning to Diva Distro for my little experimental virtual world after a year of using regular OpenSim, now that I’ve found that it’s ridiculously easy to add regions to Diva.

When I first created a little four region test grid in 2011, I used Diva on a Windows 7 machine with WAMP. It worked well, however I knew it wasn’t secure using WAMP and I wanted more than four regions, but I didn’t see how to expand beyond four regions with Diva.

After building and configuring my own OpenSUSE Linux server, I decided to try regular OpenSim instead of Diva. The challenge of installing a full OpenSim installation appealed to me, and I wanted more than four regions. I installed OpenSim with 10 regions. It went like a breeze. I had no problems. Although it’s a lot more complicated to configure than Diva, it actually installed with fewer problems than my first try with Diva. My only real problem was that I couldn’t get on the Hypergrid, which I assume was a configuration issue.

A year passed in which I had little time to work on my grid. A few friends were logging in and using it, but otherwise I wasn’t doing much with it. When I turned my attention back to it recently, my first order of business was to upgrade from OpenSim to 0.7.4. This turned out to be more of a challenge than I hoped it would be. No matter what I did, the newer version of OpenSim crashed every time I tried to run it. I don’t have a lot of time to put into it, so yesterday I decided to download the latest version of Diva (diva-r20232, which implements OpenSim 0.7.4) and to find out how hard it would be to expand beyond Diva’s basic four regions.

It was easy – trivial in fact – after noticed the following line in config-include/DivaPreferences.ini: “CombineContiguousRegions = true”. The problem is that this line causes Diva Distro to create a megaregion by default. To add regions without dealing with megaregions, all you have to do is modify the file config-include/MyWorld.ini by adding a single line. At the very beginning of the file, in the [Startup] section, add the line “CombineContiguousRegions = false”. Restart Diva and you’re all set. I created a 14 region grid, with no megaregions, using my own coordinates instead of Diva’s default 500x,500x coordinates.

To add regions, you edit Diva’s standard Regions/RegionConfig.ini file.  Copy and paste one of the existing entries to create a new entry.  Change the new entry to add the name, coordinates (Location), UUID, and port for each of your new regions. The following is what the new entry might look like:

[New Region]
RegionUUID = “11111111-2222-3333-4444-555555555554”
Location = “5002,5000”
InternalAddress = “”
InternalPort = 9004
AllowAlternatePorts = False
ExternalHostName = “SYSTEMIP”

Region Name: To add the name for your new region, simply type the new region name between the square brackets, where you see “New Region”

Region UUID: This is a unique identifier for your region. You can get your own unique UUIDs for your regions by going to the Online GUID Generator ( and generating them.

Location: This is the trickiest one.  You need to visualize your regions in a grid, numbered from the bottom up and from the left to the right.  If you start with a Location of 5000,5000 in the lower left, 5000,5001 will be directly on top of 5000,5000 and 5001,5000 will be immediately to the right of 5000,5000.  5002,5000 will be on the right side of 5001,5000, and 5010,5000 will be ten regions to the right of 5000,5000.  Assigning locations is where you’re most likely to make errors in creating your grid. If you’re going to put your grid on the Hypergrid, you probably should choose less common grid locations.

It helps to draw a chart.  It’s how I keep my 14 regions coordinated.  A chart for a basic five region grid based on Diva’s default coordinates might look like this:

My World 2
My World 4
My World 1
My World 3
New Region

Port: These should be numbered consecutively,  The default Diva configuration uses ports 9000, 9001, 9002, and 9003 for the basic four regions.  You should continue this numbering for your added regions.  The first region you add beyond the basic four will be port 9004, the next one  you add will be port 9005, etc.

I haven’t made the final decision yet to stay with Diva Distro.  I like having the full control that using regular OpenSim gives me, but considering that my time for dealing with upgrades is limited, Diva’s more automated upgrade process may make it the better choice for me.

Diva Distro can be downloaded from  The current version is as of today, September 11, 2012.  That’s the only file required to install Diva.  You’ll see a download for wifi, but that’s only for OpenSim installations running Robust.exe. Wifi is included in the Diva Distro.

2 thoughts on “Adding regions in Diva Distro”

  1. well said! We have run full robust grids with their own domains on dedicated online servers, great if you want to run hundreds of regions, but Diva allows you to quickly and efficiently run at least 9 on any standard dual core computer with 4 mb of ram, if you want more, add more ram and a get quad core processor. If you want to run multiple simulator instances running their own regions, you will still need to use Robust.

  2. Broke my diva distro adding regions somehow and now even a clean install causes socket errors. I am wondering if the old UUID’s or domain information is stored somewhere in mysql or is is something to do with a master file for the hypergird.

    How do I flush the old info and start over?

Leave a Reply to aileron Cancel reply

Your email address will not be published. Required fields are marked *